#CLOCK WIZARD HOW TO#
#CLOCK WIZARD CODE#

The Library Annex Field Guide Page Locations Opening it will reveal a large detention room with the Field Guide Page in the middle that can be revealed, along with several chests. Head all the way past the Slytherin bathrooms to a hall with several locked doors - one of which is a level 2 lock. After you gain the ability, travel down to the Slytherin Dungeons, either by going down past the Lower Grand Staircase Floo Flame, or heading to the Entrance Hall door from the Great Hall. Though physical torture is no longer utilised during detention, the aura of such horrific practices linger.To get this Field Guide Page, you’ll need to first gain second level of the the unlocking spell Alohomora by finding enough Demiguise Moonsl. This chamber allegedly served as the school’s preferred location for punishing students. Hogwarts Great Hall Field Guide Page - Slytherin Sink There are 24 Field Guide Pages to be found in The Great Hall section of Hogwarts, ranging from simple reveals to more challenging puzzles. Hogwarts - Great Hall Field Guide Page Locations Look up at the archways with Lumos to attract the moth to your wand, then take it back upstairs to get your reward. Illuminate it with Lumos to find the moth’s location.Īs it happens, the location is back down the stairs you came from, in the winding corridor hall that housed the legendary chest. It can be found at the top of the Grand Staircase Tower, past the Trophy Room Floo Flame - but you will need to have gained the Alohomora unlocking spell to unlock the level 1 gate at the end of the room.Īfter unlocking the gate, travel up through the winding passages (and grab a Legendary Chest on the first door on the left) before climbing yet more staircases past locked doors to reach a landing where the giant gargoyle sits on the left, next to the Moth Frame painting. Clock Wizard Dynamic Reconfiguration.A blank moth frame portrait that will reveal the location of a lost moth under the light of Lumos.

#CLOCK WIZARD HOW TO#

Register definitions and instructions on how to use the clock wizard through software can be found through Xilinx’s IP user guide for the Clock Wizard. This can be connected to the Zynq PS to be controlled through software. If this option is selected when configuring the IP in vivado, an AXI interface becomes availible. The Clock Wizard IP block is reconfigurable at runtime. Block Design Example with Clocking Wizard Dynamic Reconfiugration of Clock Wizard A block design example of how clocking wizard should be connected to the rest of the system is provided in figure 3. Thus, it is important to create appropriate connections with the AXI interface, processing system, and clocking wizard.

#CLOCK WIZARD CODE#

When you are using custom AXI4-Lite IP with two different clock signals (AXI clk and pixel clk) that aren’t asynchronous, you may end up with critical timing violations depending on how you’ve set up your Verilog code within your AXI4-Lite custom IP. In the figure below, two clock outputs are enabled and configured to 148.5MHz and 742.5MHz. The tool will find the closest frequencies it can get to your requests. Due to the implementation in the chip, you may not get the exact frequency you requested. On the output tab, you can enable up to 8 output clocks with requested frequency.

You can refer to Clocking Wizard Product Guide for more information Figure 1. This functionality is useful if you want to allow user to change display resolution at run time. You can also select Dynamic Reconfig and connect the AXI-Lite bus of the IP to the PS, so that ARM processor can write to the registers of the clock wizard IP and change the clock frequency while the system is running. If the primary clock comes from external pin, then you need to select proper option in the Source column. On the input page, if you are using AXI clock as the primary input source of MMCM, you need to select No Buffer under Source Column of Input Clock Information table, as it is already buffered. By default, it will use MMCM resource to synthesize the clock frequency you want. Double click the Clocking Wizard instances you added in your block design to open up the configuration dialog. In your block design, add IP Clocking Wizard. To generate different clock frequencies, you will need to use mixed-mode clock management (MMCM) units in the Xilinx FPGA.

Clock wizard